Thunder & Lightning Protection Systems (LPS & SPD)

Complete multi-zone lightning defense combining external air-termination interception, low-impedance down-conductors, equipotential earthing grids, and coordinated AC/DC/data surge protection devices.

Comprehensive Structural Interception, Earthing & Electronic Surge Defense

Bangladesh experiences some of the highest seasonal thunderstorm and lightning activity in the world. Digital Automation’s Thunder & Lightning Protection solutions integrate both External Lightning Protection Systems (ELPS — intercepting and grounding direct strikes) and Internal Surge Protection Systems (SPDs — clamping destructive induced voltage spikes before they destroy switches, servers, NVRs, solar inverters, and factory machinery).

Why It Is Needed & Problems It Solves

Even a lightning strike hitting 500 meters away induces thousands of volts along overhead power lines, buried fiber steel armor, coaxial runs, PoE camera poles, and tall factory roofs—instantly burning power supplies, SCADA PLCs, data center switches, and control boards while endangering personnel and buildings.

Air Terminal Intercepting Direct Lightning Discharge

External air-termination systems intercept direct lightning energy safely and route extreme discharge cleanly into low-resistance ground electrodes.

Practical, Operational, Financial & Safety Benefits

Safeguard Buildings & Lives

Intercept direct strikes cleanly on tall roofs, warehouses, bridge towers, and tanks—preventing structural fire, spalling concrete, and arc flash hazards.

Stop Costly Surge Burnouts

Clamp destructive transient overvoltages traveling down utility lines, CAT cables, coax, or PV strings before they ruin NVRs, routers, servers, and PLCs.

Cut Storm-Season Downtime

Coordinate Type 1 main service entrance arresters with Type 2 sub-panel and Type 3 equipment SPDs for sustained uptime through severe storms.

Shield Tall Outdoor Poles

Dedicated grounded air-terminals paired with PoE/solar DC SPDs keep exposed hilltop repeaters, CCTV masts, and PV arrays intact year-round.

Key Components Inside a Complete Lightning Protection System

Aligned with modern IEC 62305 structural interception, equipotential bonding, and coordinated surge arrestment principles.

Lightning Rod Down Conductor and Ground Electrode Schematic

Air Terminals, Masts & Down-Conductors

Elevated copper/stainless steel air-termination rods and roof conductor meshes engineered cleanly using Rolling Sphere and Protective Angle zones.

Low-Impedance Facility Earthing and Equipotential Bonding Diagram

Earth Pits, Copper Grids & Bonding Bars

Chemical/copper-bonded earth electrodes, inspection chambers, and equipotential bonding bars uniting structural steel, racks, and electrical grounds.

DIN-Rail Surge Protection Devices and Circuit Breakers

DIN-Rail AC Distribution Surge Protection

Coordinated main distribution board (MDB) Type 1+2 lightning current arresters paired with sub-panel Type 2 surge arresters clipping kV transients to safe levels.

Surge Arrester Internal Varistor Assembly

MOV / Spark-Gap Arresters, PoE & Solar DC SPDs

Thermal-disconnect Metal Oxide Varistor (MOV) & gas-tube arresters tailored separately for AC power, 600–1000V DC solar arrays, and Gigabit PoE/camera lines.

Rolling Sphere Risk Coverage

Air terminals and rooftop conductor grids are spaced strictly via geometric protection zones rather than random single poles.

Equipotential Bonding Unity

Main earth bars bond power ground, steel structure, and IT rack grounds cleanly to block destructive internal flashovers.

Verified Ground Resistance

Fall-of-Potential earth resistance testing validates conductive discharge performance prior to every system handover.

Industrial Facility AC Power Surge Protection Unit

Coordinated industrial AC/DC surge protection unit clamping high-energy lightning transients before they reach sensitive equipment.

How Coordinated Multi-Zone Strike & Surge Defense Operates Together

When thunderstorm clouds build charge above a facility, external air terminals act as the preferred strike point, channeling tens of thousands of amperes cleanly down exterior insulated/copper conductors into deep low-resistance earth pits—preventing structural fires or side-flashes. Simultaneously inside the building, Type 1, Type 2, and fine Type 3 SPDs connected via equipotential bonding divert incoming utility, solar DC, or network PoE voltage spikes into the unified ground reference within nanoseconds before returning passively to high-impedance standby.

How Our Engineers Plan, Install, Test & Hand Over Your System

Every project follows a clear four-stage engineering sequence—ensuring predictable timelines, safe installation, and clean training.

Risk & Soil Resistivity Survey

Assess building height, occupancy, roof equipment, strike exposure, and measure on-site soil resistivity (Ohms).

Protection Zone & Earthing Design

Calculate rolling-sphere coverage, separation distances, conductor routes, earth pit count & SPD tiers.

External LPS, Earth Pits & Panel SPDs

Install air terminals, down-conductors, inspection earth pits, bonding bars & MDB/DB/PoE surge modules.

Earth Resistance Test & Handover

Verify earth resistance via Fall-of-Potential testing, label test links, inspect SPD indicators & initiate periodic audits.

Where & How This Solution Operates Across Real Environments

Critical storm-season protection across high-consequence buildings, energy assets, and sensitive control electronics.

Modular AC Surge Arrester Device

Hot-Swappable DIN-Rail SPD Cartridges & Visual Fault Inspection

Main distribution boards and floor sub-panels in busy factories or offices cannot be torn apart after every heavy monsoon storm. Modular plug-in Surge Protection cartridges feature high-contrast green/red health windows—letting facility electricians spot and swap exhausted modules quickly without rewiring main breakers.

Control room workstations facing large multi-screen monitoring video wall

Protecting Command Rooms, Data Racks, Cameras & Solar Arrays Together

Control rooms and data centers represent concentrated capital—video walls, VMS NVRs, core switches, and servers sit wired to external camera poles, fiber armor, and rooftop antennas. Coordinated LPS + Internal SPD protection stops both rooftop strikes and distant utility surges from darkening command operations.

RMG Factories & Warehouses

Protecting wide-span metal roofs, chiller plants, spinning machinery & automated assembly electronics.

Solar Plants & Telecom Towers

Preventing lightning strikes and induced DC transients from destroying inverters, radios & batteries.

Outdoor CCTV Poles, Bridges & Ports

Adding dedicated pole air-terminals, earth rods, and PoE surge arresters at every field camera node.

Data Centers, Hospitals & High-Rises

Safeguarding life-safety equipment, UPS banks, medical imaging & multi-terabyte server rooms.

System Standards, Capacities & Parameters

Inspection Schedule & Operational Safety Precautions

Lightning Defense Designed Specifically by Infrastructure & Electronics Integrators

Traditional construction contractors overlook sensitive IP networks, solar DC buses, and data racks. Digital Automation protects both the concrete roof structure and the delicate IT systems operating underneath it.

Thunder, Lightning & Surge Protection Questions

Important engineering facts on grounding, surge stages, and camera/solar protection.

No. A roof lightning rod only handles direct strikes hitting the building structure. Nearby cloud-to-ground strikes induce huge voltage surges along utility power cables, outdoor camera poles, and solar strings—requiring coordinated Type 1, Type 2, and PoE/DC Surge Protection Devices (SPDs) inside electrical panels.

Modern safety standards (IEC 62305) call for all earthing systems of a building—lightning earth, power earth, and IT rack grounding—to be bonded cleanly through equipotential bonding bars (or dedicated SPD spark-gaps where needed) so huge dangerous voltage differences cannot arc sideways inside the facility.

Because long copper/Cat6 runs on steel poles pick up electromagnetic transients during nearby lightning flashes. Installing grounded local air finials, clean earth rods, and inline RJ45 PoE surge arresters at both pole and switch ends prevents costly port and camera losses.

Visual inspection of roof air-terminals, down-conductor clamps, and SPD cartridge windows—plus earth resistance testing—should be conducted annually prior to peak thunderstorm season and immediately after any known direct strike event.

Yes. Because Digital Automation engineers surveillance poles, industrial solar stations, fiber/wireless towers, and server rooms across Bangladesh, we design integrated LPS and surge protection directly into infrastructure rollouts.

Protect Your Facility, Solar Array & Network Before Peak Storms Hit

Request an on-site lightning zone survey, earth-pit audit, or panel SPD BOQ from our Dhaka team.

HQ: 35/7/A, Shantinagar, Peer Shaheber Goli, Baitul Jannat Bhaban (Ground Floor), Dhaka-1217, Bangladesh  |  Tel: +880-1632247700  |  Email: info@dgaubd.com